Components

APP5009_Commissioning Manual servoTEC S2
Category: , , ,
This commissioning manual describes work with the programmes S2 Commander and WINPAC.
APP5010_Wiring LV-servoTEC S2
Category: , , ,
In this application document, the user is given information regarding proper wiring specifically regarding the EMERGENCY OFF function with protective door monitoring and EMERGENCY OFF function without protective door monitoring.
APP5016_Opening of the protective door at a PA-CONTROL with servoTEC S2 axes
Category: , , , , , , , ,
How the axes can or may be moved on after being switched off. To solve this task, there are axis parameters, system-R-register, system markers and commands in the PA-CONTROL for which sensible application is discussed in this application document.
APP5021_servoTEC S2 - Drive via digital inputs and outputs
Category: , , ,
Description and information on: Setting of the parameters for the digital inputs and outputs, positioning, Jogging mode, referencing mode, settings in the error management, functional example with up to four destination positions, functional example with up to 16 destination positions.
APP5028_Control of the servoTEC S2 via CANopen
Category: , , ,
A servoTEC S2 is to be controlled via the CAN bus (CANopen) by a master, a PLC or a PC. The following is described in this manual: Wiring with EMERGENCY OFF and safety door monitoring, configuration of the servoTEC S2 with bus mapping, monitoring with heartbeat or node guarding, examples of the PDO communication
APP5038_Substitution of controllers in machines
Category: , , , ,
This application note shows, how to substitute a drive controller for example in case of service purposes.
Auselgerachse Modul 60/33
Category: , , , , , ,
The linear unit module 60/33 (see Figure 3, bottom) was designed for use in the commercial area. Use of a high-quality guide (guide rail and guide carriage) warrants high dynamics and good running behaviour.
Cantilever axes
Category: , , , , , , , , ,
Cantilever axes are specialised linear units for the vertical or horizontal use. Their biggest advantage is the stationary motor.
Cantilever axes Module 68
Category: , , , , , , , ,
The linear units module 68 and module 68 D are precise, linear adjustment units with toothed belt drive that are used in the commercial area as an attachment part in connection with other components.
Cantilever axes Module 90/15
Category: , , , , , , ,
The linear unit module 90/15 was designed for use in the commercial area. Use of a high-quality guide warrants high dynamics and good running behaviour. The internal guide system is protected from contamination by the side covers.
Cantilever axes Module 90/15 telescope
Category: , , , , , , ,
Design data in STEP format
Cantilever axes Module 90/15 telescope
Category: , , , , , , ,
Design data in DXF format
Cantilever axes profiLINE 37 AL
Category: , , , , , ,
Design data in STEP format
Cantilever axes profiLINE 37 AL
Category: , , , , , ,
Design data in DXF format
Direct drives euroLINE 120
Category: , , , , , ,
The linear unit euroLINE 120 is a precise, linear adjustment unit with an iron-applied linear motor that is used in the commercial area as an attachment part in connection with other components.
Direct drives euroLINE 170
Category: , , , , , ,
The linear unit euroLINE 170 is a precise, linear adjustment unit with an iron-applied linear motor that is used in the commercial area as an attachment part in connection with other components.
Direct drives euroLINE 32 KLA
Category: , , , , , ,
The linear unit euroLINE 32 KLA is a precise, straight-line adjustment unit with
ironless linear motor that is used as an attachment part in connection with other components in industrial applications
Rotary drives miniTURN 62, 80, 100
Category: , , , , , ,
Design data in STEP format
Rotary drives miniTURN 62, 80, 100
Category: , , , , , ,
Design data in DXF format
Rotary tables DT 100/140
Category: , , , , , ,
Design data in DXF format
Rotary tables DT 100/140
Category: , , , , , ,
Design data in STEP format
Rotary tables DT 80/100
Category: , , , , , ,
Design data in DXF format
Rotary tables DT 80/100
Category: , , , , , ,
Design data in STEP format
Rotary tables TP 004
Category: , , , ,
Design data in DXF format
Rotary tables TP 004
Category: , , , ,
Design data in STEP format
DT 100/140
Category: , , , , , , ,
The rotary table DT 100/140 with its compact dimensions, high parts accuracy and the soft movement process is used as an attachment in connection with other components in the commercial area.
DT 80/100
Category: , , , , , ,
The rotary table with its compact dimensions, high parts accuracy and the soft movement process is used as an attachment in connection with other components in the commercial area.
Energy chain guide system noiseLESS
Category: , , , , , , ,
When using power chains an enormously disturbing noise arises. The noiseLESS system reduces these noises by more than 20 decibel.
euroLINE 85 KL
Category: , , ,
The linear unit euroLINE 85 KL is a precise, straight-line adjustment unit with ironless linear motor that is used as an attachment part in connection with other components in industrial applications.
Guide rails and high-precision adjusters
Category: , , , , , , , , ,
For various applications IEF-Werner offers roller or sliding guides. If these guide rails are used in a complete guiding system one speaks of a slide unit, briefly slide.
Handling components
Category: , ,
The pneumatic gripping, turning and sliding modules permit easy combination with the construction kit system and thus best diversity of solutions.
Conveyor belts MINITRANS
Category: , , , , , , ,
With our wide range of conveyor belts we are able to solve various transport operations. Our modularly structured standard versions enable an uncomplicated and economic adjustment to any customer requirement respectively any ambient condition.
Power amplifier LV-servoTEC
Category: , ,
The servo amplifier are components, which are built into electrical equipment or machines, and can only be commissioned as integral components of such equipment.
Spindle drives Linear units
Category: , , , ,
The linear carriage systems are precise, linear adjustment units with spindle drive (ball thread spindle or roller thread drive). The linear carriage Systems named are used as installation parts in connection with other components in the commercial area.
LV-servoTEC S2 1xx
Category: , , ,
The servo positioning controller LV servoTEC S2 1XX (LV servoTEC servo 2nd generation) series devices are intelligent AC servo inverter with substantial parameterisation possibilities and extension options. They are flexible and can be easily adapted to a number of different applications.
LV-servoTEC S2 1xx FS
Category: , , ,
The servo positioning controller servoTEC S2100 FS series devices are intelligent AC servo inverters with substantial parameterisation possibilities and extension options.
LV-servoTEC S2 1xx FSM_STO
Category: , , ,
The safety module FSM 2.0 – STO serves as an expansion of the servo drive servoTEC S2xxx FS to achieve the safety function Safely switched-off torque – “Safe Torque Off” (STO) with SIL3 according to EN 61800-5-2 / EN 62061 / IEC 61508 or category 4 / PL e according to EN ISO 13849-1.
LV-servoTEC S2 3xx
Category: , , ,
LV servoTEC S2 3xx servo positioning controllers are intelligent AC servo converters with extensive parameterisation and extension options. Due to this flexibility, they can be adapted to numerous areas of application.
LV-servoTEC S2 3xx FS
Category: , , ,
The servo positioning controllers of the LV-servoTEC S2 xxx FS series (LV- servoTEC of the 2nd generation for Functional Safety) are intelligent AC servo inverters with extensive parameterisation and extension options.
LV-servoTEC S2 motor data base V1.44
Category: , , ,
Article-No.: 1077046
Version 1.44
LV-servoTEC S2 xxx FS MOV
Category: , , ,
The servo drive LV-servoTEC S2 xxx FS with the safety module FSM 2.0 – MOV is a product with safety relevant functions and is intended for installation in machines or automation systems.
Manual rotary adjusters and NC-rotary tables
Category: , , , , , , , ,
Manual rotary adjusters and NC-rotary tables for various application ranges - now with useful hollow shaft. Advantage: A hollow shaft allows the engineer additional scope to hide tubes and cables.
Manual adjusters domiLINE
Category: , , , , , , , , , , , , , , , , , , , , , , , , , ,
This adjustment slide system will meet any individual requirement. Every axis configuration is conceivable. Whether X-Y, X-Z, X-Y-Z or X-Y-Y-Y or, or, or... In order to cover the whole range of applications, 30, 50, 80 and 120 mm slide widths are available as standard sizes. Complete with spindle and readyassembled.
miniSPIN
Category: , , minispin
The miniSPIN-component is a compact handling unit with highly dynamic properties. The concept has been adjusted to positioning of small parts with a weight of up to 20 g.
Innovations 2017
Category: , , , , , , ,
Having the idea itself, is not yet sufficient! That‘s the motto for the year 2017.
PA-CONTROL manuals V1.20
Category: , , ,
Article-No.: 1077048
Version 1.20
PA-CONTROL MP
Category: , ,
Die PA-CONTROL MP ist eine 1-Achs-Schrittmotorsteuerung. Das Gerät ist für die Wandmontage zum Einbau in Schaltschränke konzipiert. Das Gerät besitzt eine getrennte Spannungsversorgung für das System (24 VDC) und den Motor (230 VAC).
PA-CONTROL Programmer's Manual
Category: , , , , , ,
Various elements are used for programming in PA-CONTROL.
PA-CONTROL S7 - function bloc for Profibus-connection
Category: , , , , , ,
PA-CONTROL S7 - function bloc for Profibus-connection
PA-CONTROL Interfaces
Category: , , , , , ,
Communication between the PA-CONTROL and other systems can be realized in various ways.
PA-CONTROL servoTEC
Category: , ,
The PA-CONTROL CPU5 is a Controller which was a specially developed für Installation inside an LV-servoTEC servo amplifier. The PA-CONTROL servoTEC Comes into being through the combination of the two devices.
PA-CONTROL Single/Compact/Steuergerät
Category: , , , , ,
The PA-CONTROL Single is a one-axis stepping motor control system. Depending on the device type, the 19/2" module can be assembled with either 2, 3 or 5 phase stepping Motor output stages with motor voltages of either 35V, 60V, 90V or 140V.
PA-CONTROL Smart
Category: , , ,
The PA-CONTROL Smart is a positioning and execution control system. This control system can be adjusted to different demands as regards the number of axes, the number of inputs and outputs as well as the installation surroundings.
PA-CONTROL Teachterminal
Category: , ,
This operator's manual describes the program control using the teach terminal HT-2 or the front panel of the control group PA-CONTROL.
PA-CONTROL Touch
Category: , , ,
The PA-CONTROL Touch is a positioning and execution control system.
PA-CONTROL Touch Programmer's Manual
Category: , , ,
PA-CONTROL is a sequence controller. It processes one command after another (e.g. traverse axis, set output, wait for input, etc.). Once a command has been processed, the next command in the program is executed.
Pneumatic modules
Category: , ,
The pneumatic gripping, turning and linear modules can be combined easily due to the modular design principle and thus allow an optimal solution range.
Product overview
Category: , , ,
To create sophisticated ideas is not a pure chance at IEF-Werner. It is the result of over 30 years of experience in the creation of modular components and applications. This creative process is daily ensured by more than 130 employees. Our modular components enable the realisation of customised machines in a very short time.
S2 Commander
Category: , , ,
Article-No.: 1068295
Control cabinets for servo positioning units
Category: , , , ,
IEF Werner is known as supplier for linear units equipped with motors, wiring, energy chain system, amplifi ers and control unit. If required the IEF control components are installed completely into an operational control cabinet.
Slide size 30
Category: , , , ,
The new model range of miniature slides with dovetail guides is especially made for small areas. They are suited for moving and positioning sensors, limited switches or something similar. Their solid construction in gray cast iron, make them suitable for handling machines.
Stepper motor output stage LE12-160
Category: , , , ,
The stepper motor output stage LE12-160 was developed for 2-phase stepper motors. A huge number of practical demands have been met here and a power end stage was developed that is suitable for various applications.
Stepper motor output stage LE3-80
Category: , , , ,
The LE3-80 is a position control for 2-phase stepper motors.
Stepper motor output stage LE8-80
Category: , , , ,
The LE8-80 is a position control for 2-phase stepper motors.
Swivel arm module rotaryARM radius 148,5°
Category: , ,
Design data in STEP format
Swivel arm module rotaryARM radius 199,5°
Category: , ,
Design data in STEP format
Swivel arm module rotaryARM radius 268,5°
Category: , ,
Design data in STEP format
Swivel arm units
Category: , , , , , , , minispin
As a manufacturer of automation solutions, we have to face the challenge of increasing the productivity of our machines. In order to solve these problems, innovative, flexible and simple automation components are required. For fast and precise automation tasks our rotary actuators miniSPIN and rotaryARM are most suitable.
servoTEC S2 Achsen bei Ansteuerung durch eine Siemens S7 über ProfibusDP
Category: , , ,
Zum Anschluss an ein Profibus-System muss die LV-servoTEC S2 mit einem „ProfibusDP-Modul“ ausgestattet sein. Jedes Bussegment eines PROFIBUS-Netzwerks ist mit Busabschlusswiderständen zu versehen.
Spindle drives
Category: , , , , , , , , , , , , , , , , , , , , , , ,
The IEF positioning units with spindle drive of profiLINE series were developed to combine the excellent features of a linear axis with the characteristics of a precisional slide.
Spindle drives LINE 200 GG
Category: , , , , , ,
Design data in DXF format
Spindle drives LINE 200 GG
Category: , , , , , ,
Design data in STEP format
Spindle drives LINE 250 GG
Category: , , , , , ,
Design data in DXF format
Spindle drives LINE 250 GG
Category: , , , , , ,
Design data in STEP format
Spindle drives MS 60
Category: , , , , , ,
Design data in DXF format
Spindle drives profiLINE 115
Category: , , , , , , , ,
The profiLINE 115 movement unit is a precise, linear adjustment unit with spindle drive that is used in the commercial area as an attachment part in connection with other components.
Spindle drives profiLINE 140
Category: , , , , , , , ,
The profiLINE 140 movement unit is a precise, linear adjustment unit with spindle drive that is used in the commercial area as an attachment part in connection with other components.
Spindle drives profiLINE 200
Category: , , , , , , , ,
The profiLINE 200 movement unit is a precise, linear adjustment unit with spindle drive that is used as an attachment part in connection with other components in industrial applications.
Spindle drives profiLINE 50
Category: , , , , , , , ,
The profiLINE 50 module is a precise, linear adjustment unit with spindle drive that is used in the commercial area as an attachment part in connection with other components.
Spindle drives profiLINE 70
Category: , , , , , , , ,
The profiLINE 70 movement unit is a precise, linear adjustment unit with spindle drive that is used as an attachment part in connection with other components in industrial applications.
WINPAC Update V6.20 with manuals
Category: , , ,
Article-No.: 1002912
Version 6.20
Toothed belt- bzw. Spindle drives Module 105(S) and Modul 142(S)
Category: , , , , , , , , , , ,
The linear units module 105 and module 142 are precise linear adjustment units with circumfering toothed-belt drive. The types module 105 S and module 142 S are equipped with spindle drives (ball roller or trapezoid spindle). All linear units named are used as installation parts in connection with other components in the commercial area.
Toothed belt drives easyLINE
Category: , , , , , , , ,
The easyLINE module is a precise, linear adjustment unit with toothed belt drive that is used in the commercial area as an attachment part in connection with other components.
Toothed belt drives easyLINE Positionierpaket
Category: , , , , , , ,
Design data in DXF format
Toothed belt drives easyLINE Positionierpaket
Category: , , , , , , ,
Design data in STEP format
Toothed belt drives easyLINE S
Category: , , , , , , ,
The linear module type easyLINE S is a precise, linear positioning unit having a toothbelt drive system. The wide range of IEF Werner linear products can be used for many kinds of industrial automation, either integrated with new or existing automation or in combinations with other IEF Werner linear modules.
Toothed belt drives Module 115/42 (B)
Category: , , , , , , , ,
The linear unit module 115/42 was designed for use in the commercial area. Use of a high-quality guide warrants high dynamics and good running behaviour. The internal guide system is protected from contamination by the toothed belt.
Toothed belt drives Module 160/15
Category: , , , , , , , ,
The linear unit module 160/15 was designed for use in the commercial area.
Use of a high-quality guide warrants high dynamics and good running behaviour. The internal guide system is protected from contamination by the toothed belt.
Toothed belt drives Module 160/15 G
Category: , , , , , , , , , ,
The linear drive unit Module 160/15 G (G means ‘Gegenläufig’ = 'in opposing directions’; was designed for industrial applications. The use of a high-quality guide ensures high dynamics and good running characteristics. The guide elements have special seals which protect them from coarse dirt.
Toothed belt drives Module 160/15 ZR 10
Category: , , , , , , , ,
The linear unit Module 160/15 ZR10 was designed for use in the commercial area. Use of a high-quality guide warrants high dynamics and good running behaviour. The internal guide system is protected from contamination by the toothed belt.
Toothed belt drives Module 65/15
Category: , , , , , , , ,
The linear unit module 65/15 was designed for use in the commercial area. Use of a high-quality guide warrants high dynamics and good running behaviour. The internal guide system is protected from contamination by the toothed belt.
Toothed belt drives Module 80/15
Category: , , , , , , , ,
The linear unit module 80/15 was designed for use in the commercial area. Use
of a high-quality guide warrants high dynamics and good running behaviour. The internal guide system is protected from contamination by the toothed belt.

HINWEIS! Diese Website verwendet Cookies und ähnliche Technologien. Wenn Sie die Browser-Einstellungen nicht verändern, stimmen Sie zu.

OK